华为AP3010DN-AGN刷固件方法

AP3010DN-AGN胖FAT转瘦FIT命令如下:

方法一:

[Huawei]interface vlan 1
[Huawei-Vlanif1]ip address 169.254.1.1 255.255.0.0  //默认就是这个,此处可略过
[Huawei-Vlanif1]quit

本机IP设置 169.254.1.200 255.255.0.0 并开启3CDaemon(下载地址:http://blog.wmphp.com/down/3CDaemon.zip ),输入如下命令,完成FAT转Fit模式。终端工具:SecureCRT6.2.0(下载地址:http://blog.wmphp.com/down/SecureCRT.zip

ap-mode-switch prepare
ap-mode-switch check
ap-mode-switch tftp FitAP3X10XN_V200R006C20SPC800.bin 169.254.1.200

方法二:

Uboot升级

开启3秒左右,看到提示

Press f or F  to stop Auto-Boot in 3 seconds:  3          //按F键进入Uboot模式
Password for uboot cmd line :   //输入密码admin@huawei.com

  1. 配置AP和tftp服务器的IP地址,保证AP能够从tftp服务器获取升级文件。

ar7240> setenv ipaddr 169.254.1.1  #AP的IP地址
ar7240> setenv serverip 169.254.1.200   #服务器的IP地址
ar7240> saveenv
Saving Environment to Flash...
Erasing Flash...Writing to Flash... done

  1. 在命令行中键入update boot,在下面的显示信息中作相应的配置:
    1. 升级uboot:

ar7240> update boot            #u-boot.bin存放在TFTP目录下
dup 1 speed 1000
......
Copy to Flash... done
r7240> reset                      #以新加载的uboot启动

升级uboot时不能断电,否则AP无法启动。

  1. 重新启动AP。在出现以下信息后3秒内按下F键,进入uboot命令行视图。

Uboot菜单缺省密码为admin@huawei.com。

Press f or F  to stop Auto-Boot in 3 seconds:  3
Password for uboot cmd line :
ar7240>

加载需要升级的bin FiT AP系统软件:

ar7240> update system FitAP3X10XN_V200R006C20SPC800.bin       #系统bin存放在TFTP目录下
dup 1 speed 1000
......
Upgrade Firmware to A Successful

  1. 配置完成后,在命令行中键入reset,AP就会使用指定的网络启动固件文件启动了。用这种方式启动后,固件被读入AP的flash。

ar7240> reset
Resetting...

  1. 升级完成后,可执行命令display version查看当前版本是否升级成功。此方法没有方法一实用,而且有风险,小编也没用,只是列出来供大家参考

AP3010DN-AGN  S/N:2102355829w0e5005614

AP为FAT模式时已开启WEB网管

默认的IP 169.254.1.1 掩码:255.255.0.0

默认用户名 admin 密码:admin@huawei.com

(1)用户视图(查看交换机的简单运行状态和统计信息)<Quidway>:与交换机建立连接即进入
(2)系统视图(配置系统参数)[Quidway]:在用户视图下键入system-view
(3)以太网端口视图(配置以太网端口参数)[Quidway-Ethernet0/1]:在系统视图下键入interface ethernet 0/1
(4)VLAN视图(配置VLAN参数)[Quidway-Vlan1]:在系统视图下键入vlan 1
(5)VLAN接口视图(配置VLAN和VLAN汇聚对应的IP接口参数)[Quidway-Vlan-interface1]:在系统视图下键入interface vlan-interface 1
(6)本地用户视图(配置本地用户参数)[Quidway-luser-user1]:在系统视图下键入local-user user1
(7)用户界面视图(配置用户界面参数)[Quidway-ui0]:在系统视图下键入user-interface

sys 回车 进入全局模式
quit 退回到用户
save 保存
Ctrl+Z 换一行
-----
<huawei>reset saved-configuration 恢复出厂值,交换机重置

<huawei>reset factory AP重置
reboot
N 不要存在配置
Y 确定重启
-----
按RESET键 恢复出厂设置

display current-configuration 显示当前配置

[Huawei]display current-configuration
#
snmp-agent local-engineid 800007DB03002520130280
snmp-agent
#
http secure-server ssl-policy default_policy
http server enable
#
clock timezone Bei Jing Time add 08:00:00
#
info-center timestamp log format-date
#
dns resolve
#
lldp enable
#
pki realm default
enrollment self-signed
#
ssl policy default_policy type server
pki-realm default
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password irreversible-cipher %@%@X"rg8gLdnWFsme+%Cme&|WpR_ry&% h+8uUz%T^ED_a&~WpU|%@%@
local-user admin privilege level 15
local-user admin service-type ssh http
#
interface Vlanif1
ip address 169.254.1.6 255.255.0.0
#
interface GigabitEthernet0/0/0
#
interface Wlan-Bss1
permit-domain name default
force-domain name default
#
interface Wlan-Bss2
permit-domain name default
force-domain name default
#
interface NULL0
#
ssh client first-time enable
stelnet server enable
undo telnet server enable
#
user-interface con 0
authentication-mode password
set authentication password cipher %@%@aY1{WW$UkOsye(PSBDV<,.N396-.8l8z{(x]8'1w N5"B.N6,%@%@
user-interface vty 0 4
authentication-mode aaa
protocol inbound ssh
user-interface vty 16 20
#
wlan
wmm-profile name default id 0
wmm-profile name BUBA id 1
wmm-profile name BUBA-5G id 2
traffic-profile name default id 0
security-profile name default id 0
security-profile name BUBA id 1
security-policy wpa-wpa2
wpa-wpa2 authentication-method psk pass-phrase cipher %@%@H:=$MFJ{7KD]Bj.5u[X6 *)Of%@%@ encryption-method tkip-ccmp
service-set name BUBA id 0
Wlan-Bss 1
ssid BUBA
user-isolate
traffic-profile id 0
security-profile id 1
service-set name BUBA-5G id 1
Wlan-Bss 2
ssid BUBA-5G
user-isolate
traffic-profile id 0
security-profile id 1
radio-profile name default id 0
wmm-profile id 0
radio-profile name BUBA id 1
channel-mode fixed
wmm-profile id 1
radio-profile name BUBA-5G id 2
channel-mode fixed
wmm-profile id 2
#
interface Wlan-Radio0/0/0
radio-profile id 1
service-set id 0 wlan 1
#
interface Wlan-Radio0/0/1
radio-profile id 2
channel 40MHz-minus 64
service-set id 1 wlan 1
#
return

新配置

[Huawei]display saved-configuration
[V200R005C00SPC600]
#
ftp server enable
set default ftp-directory flash:
#
snmp-agent local-engineid 800007DB03002520130280
snmp-agent
#
http secure-server ssl-policy default_policy
http server enable
#
clock timezone Bei Jing Time add 08:00:00
#
info-center timestamp log format-date
#
dns resolve
#
lldp enable
#
pki realm default
enrollment self-signed
#
ssl policy default_policy type server
pki-realm default
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password irreversible-cipher %@%@X"rg8gLdnWFsme+%Cme&|WpR_ry&%h+8uUz%T^ED_a&~WpU|%@%@
local-user admin privilege level 15
local-user admin service-type ssh http
#
interface Vlanif1
ip address 169.254.1.1 255.255.0.0
#
interface GigabitEthernet0/0/0
#
interface Wlan-Bss1
description Wlan-Bss1
permit-domain name default
force-domain name default
#
interface Wlan-Bss2
description Wlan-Bss2
permit-domain name default
force-domain name default
#
interface NULL0
#
ssh client first-time enable
sftp server enable
stelnet server enable
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
authentication-mode aaa
protocol inbound all
user-interface vty 16 20
authentication-mode aaa
#
wlan
wmm-profile name default id 0
wmm-profile name BUBA id 1
wmm-profile name BUBA_5G id 2
traffic-profile name default id 0
security-profile name default id 0
security-profile name BUBA id 1
security-policy wpa2
wpa2 authentication-method psk pass-phrase cipher %@%@if;4CqM.u77|F!9HZGQ~x&k9%@%@ encryption-method tkip-ccmp
service-set name BUBA id 0
Wlan-Bss 1
ssid BUBA
user-isolate
traffic-profile id 0
security-profile id 1
service-set name BUBA_5G id 1
Wlan-Bss 2
ssid BUBA_5G
user-isolate
traffic-profile id 0
security-profile id 1
radio-profile name default id 0
wmm-profile id 0
radio-profile name BUBA id 1
wmm-profile id 1
radio-profile name BUBA_5G id 2
wmm-profile id 2
#
interface Wlan-Radio0/0/0
radio-profile id 1
service-set id 0 wlan 1
#
interface Wlan-Radio0/0/1
radio-profile id 2
service-set id 1 wlan 1
#
return

END
如本资源侵犯了您的权益,请联系投诉邮箱admin@wmphp.com进行举报!我们将在收到邮件的1个小时内处理完毕。 本站仅为平台,发布的资源均为用户投稿或转载!所有资源仅供参考学习使用,请在下载后的24小时内删除,禁止商用! Wmphp.com(完美源码)助力正版,如您有自己的原创产品,可以联系客服投稿,代理出售! Wmphp.com(完美源码)客服QQ:136882447 Wmphp.com(完美源码)商务电话(仅对企业客户/个人用户):15120086569 (微信同步) 请注意:本站不提供任何免费的技术咨询服务,为了节约时间,下载前 请确认自己会技术
完美源码 » 华为AP3010DN-AGN刷固件方法
3718+

本站勉强运行

6069+

用户总数

695+

资源总数

1+

今日更新

2024-12-5

最后更新时间